FLex 100 type solar panel
Flex type efficiency up to 22%
High efficiency FLex panel waterproof 100W solar panel is perfect for permanent outdoor use to provide free electricity for charging 12V batteries to power various applications, such as in a motor home, caravan, camper, boat, or for solar lighting systems, off-grid and back up solar power systems, and complete household solar power systems.
Back-contact solar cells with efficiency up to 22% make this panel ideal for applications where space is restricted, or there are obstructions on the roof. The panel can also be used to provide direct power supply for applications not sensitive to changes in input voltage / current (e.g. electric motors or pumps) and for various grid-tie applications.
The panel is incredibly light which is great for all vehicles.
This type panel suitable for bonding onto the roof of a caravan, motorhome, boats, mobile catering units and sport event trailers.
- Its maximum bending radius of 30 ° and a thickness of only 4mm;
- Suitable for curved surface like the deck of a boat or the roof of an RV .
- With proper installation it is suitable to run over it.
- Assembly is easy to realize itself with the kit available in our shop or through the 4 connection holes in the corners of the panel .
- All our solar panels are made up of Class A high efficiency U.S.solar cells. These cells reach their high efficiency including through the metal contacts. Moving from the front to the rear and by the broadening of the contacts , there is less loss power .
FLex 100 specification
|Voltage at Pmax（Vmp）:
|Current at Pmax（Imp）:
|Open circuit voltage（Voc）:
|Short circuit current（Isc）:
|Max system voltage（VDC）:
||-40℃ to + 85℃
|Temperature Coefficient of Pmax:
|Temperature Coefficient of voc:
|Temperature Coefficient of ISC:
|Nominal Operating Cell Temperature:
|Data under standard testing conditions(STC)
|Type of Connector:
New generation FLex 2 solar panel
1).Flexible Angle : up to 20 degree
2).Back Sheet: aluminum or fiberglass (PCB)
3).J-Box: IP 67 rated
4).Thickness of ET: 0.025mm
5).Thickness of solar panel: 2.5mm or 3mm
6).Cables/Connector: 1.5meters, 2*2.5mm2 cable with MC4 connectors
7).Type of Solar Cells: Monocrystalline silicon cells
8).Eyelets: 4pcs in the corners
9). By pass diode: 2pcs (10A for each )
1).Peak Power(Pmax)—————————————– 100W
2).Maximum Power Voltage (Vmp)————————— 18V
3).Maximum Power Current (Imp)————————— 5.56A
4).Open Circuit Voltage (Voc)———————————- 21.24V
5).Short Circuit Current (Isc)———————————– 6.11A
6).Maximum System Voltage———————————- DC 500V
7).Cell Efficiency————————————————– 18%
8).Power Tolerance———————————————- ±3%
9).Number of Cells———————————————– 36pcs
10).Operating Temperature———————————— -20~+50°C
11).Storage Temperature————————————— -20~+30°C
12).Temperature Coefficients of Isc(%)——————— +0.09%/°C
13).Temperature Coefficients of Pmax(%)—————– -0.37%/°C
14).Temperature Coefficients of Voc(%)——————– -0.34%/°C
(Test Condition: AM=1.5，E=1000W/㎡ ，Tc=25°C)
1).Solar Panel Size (1pc) 1245*550*2.5mm
Performance of ET vs. PET
||Ultra lightweight and durable. The combination between ET and back sheet is much stronger than PET.
||Combination of PET and back sheet cracks easily, is not durable, and also not waterproof.
||Includes a 0.025mm thin, UV resistant, layer of protection. Total thickness less than 0.1mm.
||0.15mm thick. Solar cells break easily due to low hardness.
||95% transparency offers excellent efficiency in terms of light to electricity conversion.
||90% to 93% transparent results in lower efficiency in terms of light to electricity conversion.
||ET has non-adhesive surface properties. Highly stain-resistant and easily gets cleaned by the rain.
||Adhesive surface often gets covered with dust or other debris, significantly affecting the output of solar panel.
||Lifetime of 10 years. Resists aging, deteriorates slowly.
||Lifetime of at most 5 years. Easily forms air pockets and peels off.
||Highly resistant to seawater corrosion.
||Not acid and alkali resistant, making it totally unsuitable for use in marine environment.
||Highly flame retardant. Suitable for use in temperatures ranging from -65°C to +150°C. Can be installed safely in hot climates.
||Not suitable for use in high temperature regions due to short-term heat resistance.
||Absorbs sunlight. Does not reflect it.
||Reflects a large amount of sunlight, producing glare and creating traffic risks to cars and airplanes.
SolPlant 200 solar panel
The SolPlant series is a new generation of solar modules. The frameless encapsulation of solar cells between TPO or PVC and glass provides maximum mechanical stability, durability and ease of use for roofing applications, becoming a revolutionary solution for implementation. The fast and easy apllication of the modules will change the solar roof market in an astonishing way. With a size of about 1600 mm to 1200 mm and a weight of about 12 kg the modules can be installed easily. The 2mm front glass is tempered and very resistant to hail and other mechanical impacts.